Pool Safety

POOL FENCING

Queensland regulations require that all swimming pools be fenced unless specifically exempted.

Fences must be at least 1.2 m high and gates must be self closing and self latching. The fencing must separate the pool from residential buildings and neighbouring properties.

MAJOR POINTS

  • Fencing requirements must be met prior to filling the pool
  • Fencing and gates should be checked periodically to ensure they continue to satisfy the regulations
  • Don't leave furniture or other items that children can climb on near your pool fence or above-ground pool.

POOL COVERS

Swimming pool covers of various types are used to keep dust and leaves out of pools and to retain heat within pools. Most pool covers do not provide protection against children getting into the pool, and may present a hazard in that if a child does get into the pool under the cover they cannot be seen.

Some pool covers may give the illusion of being solid and encourage a child to attempt to walk on it. This will cause the cover to sag and the child may drown in pool water or accumulated rain water.

When the pool is being used, the cover should be removed. The cover should never be left partially over the pool.

Pool covers should never be considered a substitute for a fence or proper supervision.

USE OF THE POOL

Most domestic pools are not designed for diving. Unless your pool has been specifically built for this purpose, you should not allow pool users to dive. You should also ensure that obstacles which may be used as diving platforms are not placed near the pool.

Severe injuries can result from divers hitting the side or bottom of pools - you are therefore protecting your family and friends by adopting a NO DIVING policy!

The same can be said for “rough-house” play around or in the pool.

We suggest that you should display a “NO DIVING” sign in your pool area and affix depth markers on or near the pool. Diving boards, slippery dips, trampolines etc. can be dangerous and should only be used if your pool has been specifically designed for their safe use. Even then, constant adult supervision is important to prevent accidents.

Ensure that your pool is clearly visible from the house.

MAJOR POINTS

- Supervise pool users at all times
- A little thought can prevent accidents from happening.
- Place “NO DIVING” signs near your pool unless it has been specifically designed to allow safe diving.
- Drinking and swimming don't mix - don't allow alcohol to be consumed by pool users.
- Keep glasses and other breakables away from the pool area - using plastic can prevent injury.

Is your pool fence legal?

!!REMEMBER!!
there is NO SUBSTITUTE for ADULT SUPERVISION of pool users AT ALL TIMES

Is your pool or Spa water safe?

Untreated, or improperly treated water can be a health threat. Chemically balanced and sanitised water, on the other hand, will provide a healthy and visually appealing environment for you, your family and friends.

Balanced water means that chemical demands have been met. If the chemical levels are too low the water will aggressively seek the products it needs by attacking the pool surface and equipment. This may lead to severe corrosion problems. On the other hand, high chemical levels may lead to the formation of scale on the pool surfaces and equipment.

Out of balance water can, therefore, cause expensive damage to the pool and may also inhibit the sanitising process.

In simple terms, the pool owner should balance the following variables:

  • pH
  • Total Alkalinity
  • Calcium Hardness

pH.

pH is a measure of how acidic or alkaline the water is. The pH scale ranges from 0 to 14, with 7.0 being neutral. Values below 7.0 are acidic, and values above 7.0 are alkaline. With pool water we are seeking a pH balance suitable to the pool user, the pool and sanitiser use. Australian Standard 3633 defines the operating range as 7.0 to 7.8 and the recommended range of 7.2 to 7.6 (SPASA recommend 7.0 to 7.2 for fibreglass pools).

Topping up your pool, heavy rain, heavy bathing loads and chemical additions can all change the pH level of your pool water. Incorrect pH levels can have the following effects;

  • Cause swimmer discomfort (itchy skin, red eyes etc)
  • Interfere with the action of your pool sanitiser.

THE EFFECT OF pH ON CHLORINE

Effective sanitising relies on pH values. Therefore, sanitiser and pH levels should be the measures you check and adjust most often. Regardless of the chlorine type or the chlorination process used, any pH drift above the recommended range (7.0 to 7.8) will inhibit the sanitising effect of your chlorine.

TOTAL ALKALINITY (T.A.)

This is a measure of bi-carbonates, carbonates and hydroxides in your water. The Australian Standard 3633 recommends a range of 60 to 200 parts per million (ppm). Your pool builder or pool shop will advise you of the recommended level for your pool.

Low T.A. will lead to erosion of the surface of concrete and painted pools. It will also cause the pH levels to be very unstable with small additions of chemicals resulting in major shifts in pH.

This is sometimes known as “pH bounce”.Total Alkalinity can be changed in the following ways;

adding buffer (bi-carbonate of soda). This RAISES the Total Alkalinity.
adding acid to your pool to lower pH will also LOWER Total Alkalinity.
topping-up your pool will change the Total Alkalinity depending on the T.A. of the top-up water.

THE INTERCONNECTION BETWEEN pH AND TOTAL ALKALINITY.

It can be seen that acids will lower the pH and Total Alkalinity. There is an interconnection between these two chemical components and, because of this, they need to be adjusted together. The levels you are seeking to maintain are;

  • pH of 7.2 to 7.8 (7.0 to 7.2 - fibreglass pools)
  • Total Alkalinity of approx 100 to 120 ppm (60-200 is the recommended range). Check with your pool builder or pool shop for the level required in your pool.

Lets assume that the pH is OK but the Total Alkalinity is low. To raise the level, add “buffer” (Sodium Bicarbonate) at the required rate. However Buffer is an alkali and will also raise pH.

Acid (Hydrochloric Acid or Sodium Bisulphate), which is used to lower pH, also lowers T.A. The trick is therefore to raise the T.A. artificially high so that when acid is added, to lower the pH to the correct level, the T.A. is also reduced to the correct range.

Note: Hydrochloric Acid must always be diluted (one part acid to ten parts of water) prior to adding to the pool. Always add acid to water, never water to acid.

CALCIUM HARDNESS

In simple terms, this measures the amount of dissolved calcium in your pool water. The recommended range is 80 to 500ppm according to Australian Standard 3633.

Both Total Alkalinity and Calcium Hardness need to be brought into balance. If not, low levels will mean the water is corrosive to the pool and/or equipment; high levels will lead to scale formation on pool and equipment.

Calcium hardness tests cannot usually be performed with the standard test kit. We suggest a water sample be taken to a S.P.A.S.A. Accredited Pool Shop for testing. A rough rule of thumb in areas where calcium levels are not naturally high is that testing annually will suffice after the initial adjustment. The only qualification to this is if you are using Calcium Hypochlorite to sanitise your pool. This chemical raises Calcium Hardness levels which may require more frequent testing and adjustment.

ADDING CHEMICALS

As a general rule you are far better off adding small amounts of chemicals, running the filter and testing the effect after several hours. Attempting LARGE chemical changes by adding LARGE amounts of chemicals can result in BIG PROBLEMS.

Too Complicated? We can help.

Free In Store Water Testing